Alcatel-Lucent IAP93 Betriebsanweisung PDF herunterladen (Seite 103)

103 | Wired Profiles AOS-W Instant 6.3.1.1-4.0 | User Guide

a. Name— Specify a name for the profile.

b. Primary Usage — Select Employee or Guest.

c. Speed/Duplex — Ensure that appropriate values are selected for Speed/Duplex. Contact your network

administrator if you need to assign speed and duplex parameters.

d. POE — Set POE to Enabled to enable Power over Ethernet.

The E2 port on OAW-RAP3WNP supports Power Sourcing Equipment (PSE) to supply power to any compliant

802.3af powered (class 0-4) device. OAW-RAP155P supports PSE for 802.3af powered device (class 0-4) on one

port (E1 or E2), or 802.3at powered DC IN (Power Socket) on two ports (E1 and E2).

e. Admin Status — Ensure that an appropriate value is selected. The Admin Status indicates if the port is up or

down.

f. Content Filtering— To ensure that all DNS requests to non-corporate domains on this wired network are sent

to OpenDNS, select Enabled for Content Filtering.

g. Uplink — Select Enabled to configure uplink on this wired profile. If Uplink is set to Enabled and this network

profile is assigned to a specific port, the port will be enabled as Uplink port. For more information on assigning

a wired network profile to a port, see Assigning a Profile to Ethernet Ports on page 108.

h. Spanning Tree—Select the Spanning Tree checkbox to enable Spanning Tree Protocol (STP) on the wired

profile. STP ensures that there are no loops in any bridged Ethernet network and operates on all downlink

ports, regardless of forwarding mode. STP will not operate on the uplink port and is supported only on OAW-

IAPs with three or more ports. By default Spanning Tree is disabled on wired profiles.

4. Click Next. The VLAN tab details are displayed.

5. Configure VLAN for the wired profile. For more information, see Configuring VLAN for a Wired Profile on page

103.

In the CLI

To configure wired settings for:

(Instant Access Point)(config)# wired-port-profile <name>

(Instant Access Point)(wired ap profile <name>)# type {<employee> |<guest>}

(Instant Access Point)(wired ap profile <name>)# speed {10 |100 |1000 |auto}

(Instant Access Point)(wired ap profile <name>)# duplex {<half>|<full>|<auto>}

(Instant Access Point)(wired ap profile <name>)# no shutdown

(Instant Access Point)(wired ap profile <name>)# poe

(Instant Access Point)(wired ap profile <name>)# uplink-enable

(Instant Access Point)(wired ap profile <name>)# content-filtering

(Instant Access Point)(wired ap profile <name>)# spanning-tree

(Instant Access Point)(wired ap profile <name>)# end

(Instant Access Point)# commit apply

Configuring VLAN for a Wired Profile

If you are creating a new wired profile, complete the WiredSettings procedure before configuring VLAN. For more

information, see Configuring Wired Settings on page 102.

You can configure VLAN using AOS-W Instant UI or CLI.

In the AOS-W Instant UI

To configure VLAN:

1. In the VLAN tab, enter the following information.

a. Mode — You can specify any of the following modes:

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 ... 334 335

Kommentare zu diesen Handbüchern

Keine Kommentare

Alcatel-Lucent IAP93 Betriebsanweisung Seite 103

Kommentare zu diesen Handbüchern