Alcatel-Lucent IAP93 Betriebsanweisung PDF herunterladen (Seite 216)

216 | Adaptive Radio Management AOS-W Instant 6.3.1.1-4.0 | User Guide

Parameter Description

Customize Valid

Channels

Select this check box to customize valid channels for 2,4 GHz and 5 GHz. By default,

the AP uses valid channels as defined by the Country Code (regulatory domain). On

selecting the Customize Valid Channels check box, a list of valid channels for both

2.4.GHz and 5 GHz are displayed. The valid channel customization feature is

disabled by default.

Minimum

Transmit Power

Specify the minimum transmission power. The value specified for Minimum Transmit

Power indicates the minimum Effective Isotropic Radiated Power (EIRP) from 3 to 33

dBm in 3 dBm increments. If the minimum transmission EIRP setting configured on

an AP is not supported by the AP model, this value is reduced to the highest

supported power setting. The default value is for minimum transmit power is 18 dBm.

Maximum

Transmit Power

Specify the maximum transmission power. The value specified for Maximum

Transmit Power indicates the maximum Effective Isotropic Radiated Power (EIRP)

from 3 to 33 dBm in 3 dBm increments. If the maximum transmission EIRP configured

on an AP is not supported by the AP model, the value is reduced to the highest

supported power setting. The default value for maximum transmit power is 127 dBm.

Client aware

Select Enabled to allow ARM to control channel assignments for the APs with active

clients. When the Client aware mode is set to Disabled, the OAW-IAP may change to

a more optimal channel, which change may disrupt current client traffic. The Client

aware option is Enabled by default.

Scanning

Select Enabled so that the OAW-IAP dynamically scans all 802.11 channels within its

802.11 regulatory domain at regular intervals and reports to the OAW-IAP. This

scanning report includes WLAN coverage, interference, and intrusion detection data.

NOTE: For client match configuration, ensure that scanning is enabled.

Wide Channel

Bands

Select a band to allow the APs to be placed in 40Mhz (wide band) channels. The

Wide channel band allows administrators to configure 40 MHz channels in the 2.4

GHz and 5.0 GHz bands. 40 MHz channels are two 20 MHz adjacent channels that

are bonded together. 40 MHz channel effectively doubles the frequency bandwidth

available for data transmission.

For high performance, you can select 5GHz. If the AP density is low, enable in the

2.4GHz band.

80 MHz Support Enables or disables the use of 80 MHz channels on APs. This feature allows ARM to

assign 80 MHz channels on APs with 5GHz radios, which support a very high

throughput. This setting is enabled by default.

NOTE: Only the APs that support 802.11ac can be configured with 80 MHz

channels.

Table 41:

Access Point Control - Configuration Parameters

7. Reboot the OAW-IAP.

8. Click OK.

In the CLI

To configure ARM features on an OAW-IAP with 5 GHz radio:

(Instant Access Point)(config)# arm

(Instant Access Point)(ARM)# a-channels <5GHz-channels>

(Instant Access Point)(ARM)# min-tx-power <power>

(Instant Access Point)(ARM)# max-tx-power <power>

(Instant Access Point)(ARM)# band-steering-mode {<Prefer 5 GHz>| <Force 5 GHz>|<Balance Bands>

|<Disabled>}

1 2 ... 211 212 213 214 215 216 217 218 219 220 221 ... 334 335

Kommentare zu diesen Handbüchern

Keine Kommentare

Alcatel-Lucent IAP93 Betriebsanweisung Seite 216

Kommentare zu diesen Handbüchern