Alcatel-Lucent IAP93 Betriebsanweisung PDF herunterladen (Seite 115)

115 | Captive Portal for Guest Access AOS-W Instant 6.3.1.1-4.0 | User Guide

f. Content Filtering— To ensure that all DNS requests to non-corporate domains on this wired network are sent

to OpenDNS, select Enabled for Content Filtering.

g. Uplink — Select Enabled to configure uplink on this wired profile. If Uplink is set to Enabled and this network

profile is assigned to a specific port, the port will be enabled as Uplink port. For more information on assigning

a wired network profile to a port, see Assigning a Profile to Ethernet Ports on page 108.

4. Click Next. The VLAN tab details are displayed.

5. Enter the following information.

a. Mode — You can specify any of the following modes:

l Access — Select this mode to allow the port to carry a single VLAN specified as the native VLAN.

l Trunk — Select this mode to allow the port to carry packets for multiple VLANs specified as allowed

VLANs.

b. Specify any of the following values for Client IP Assignment:

l Virtual Controller Assigned: Select this option to allow the Virtual Controller to assign IP addresses to

the wired clients. When the Virtual Controller assignment is used, the source IP address is translated for

all client traffic that goes through this interface. The Virtual Controller can also assign a guest VLAN to a

wired client.

l Network Assigned: Select this option to allow the clients to receive an IP address from the network to

which the Virtual Controller is connected. On selecting this option, the New button to create a VLAN is

displayed. Create a new VLAN if required.

c. If the Trunk mode is selected:

l Specify the Allowed VLAN, enter a list of comma separated digits or ranges 1,2,5 or 1-4, or all. The

Allowed VLAN refers to the VLANs carried by the port in Access mode.

l If Client IP Assignment is set the Network Assigned, specify a value for Native VLAN. A VLAN that

does not have a VLAN ID tag in the frames is referred to as Native VLAN. You can specify a value within

the range of 1-4093.

d. If the Access mode is selected:

l If the Client IP Assignment is set to Virtual Controller Assigned, proceed to step 2.

l If the Client IP Assignment is set the Network Assigned, specify a value for Access VLAN to indicate

the VLAN carried by the port in the Access mode.

6. Click Next to configure internal or external Captive portal authentication, roles and access rules for the guest

users.

In the CLI

To configure wired settings for:

(Instant Access Point)(config)# wired-port-profile <name>

(Instant Access Point)(wired ap profile <name>)# type <guest>

(Instant Access Point)(wired ap profile <name>)# speed {10 |100 |1000 |auto}

(Instant Access Point)(wired ap profile <name>)# duplex {<half>|<full>|<auto>}

(Instant Access Point)(wired ap profile <name>)# no shutdown

(Instant Access Point)(wired ap profile <name>)# poe

(Instant Access Point)(wired ap profile <name>)# uplink-enable

(Instant Access Point)(wired ap profile <name>)# content-filtering

To configure VLAN settings for a wired profile:

(Instant Access Point)(config)# wired-port-profile <name>

(Instant Access Point)(wired ap profile <name>)# switchport-mode {<trunk> | <access>}

(Instant Access Point)(wired ap profile <name>)# allowed-vlan <vlan>

(Instant Access Point)(wired ap profile <name>)# native-vlan {<guest|1…4095>}

To configure a new VLAN assignment rule:

1 2 ... 110 111 112 113 114 115 116 117 118 119 120 ... 334 335

Kommentare zu diesen Handbüchern

Keine Kommentare

Alcatel-Lucent IAP93 Betriebsanweisung Seite 115

Kommentare zu diesen Handbüchern