Alcatel-Lucent IAP93 Betriebsanweisung PDF herunterladen (Seite 58)

Graph

Name

Description Monitoring Procedure

Clients The Clients graph shows the number of

clients associated with the selected OAW-

IAP for the last 15 minutes.

To see an enlarged view, click the graph.

The enlarged view provides Last,

Minimum, Maximum, and Average

statistics for the number of clients

associated with the OAW-IAP for the last

15 minutes.

To see the exact number of clients

associated with the selected OAW-IAP at a

particular time, hover the cursor over the

graph line.

To check the number of clients associated with the

OAW-IAP for the last 15 minutes,

1. Log in to the AOS-W Instant UI. The Virtual

Controller view is displayed. This is the default

view.

2. In the Access Points tab, click the OAW-IAP for

which you want to monitor the client association.

The OAW-IAP view is displayed.

3. Study the Clients graph. For example, the graph

shows that six clients are associated with the OAW-

IAP at 12:11 hours.

Throughput The Throughput graph shows the

throughput for the selected OAW-IAP for

the last 15 minutes.

l Outgoing traffic — Throughput for

outgoing traffic is displayed in green.

Outgoing traffic is shown about the

median line.

l Incoming traffic — Throughput for

incoming traffic is displayed in blue.

Incoming traffic is shown below the

median line.

To see an enlarged view, click the graph.

l The enlarged view provides Last,

Minimum, Maximum, and Average

statistics for the incoming and outgoing

traffic throughput of the OAW-IAP for

the last 15 minutes.

To see the exact throughput of the selected

OAW-IAP at a particular time, hover the

cursor over the graph line.

To check the throughput of the selected OAW-IAP for

the last 15 minutes,

1. Log in to the AOS-W Instant UI. The Virtual

Controller view is displayed. This is the default

view.

2. In the Access Points tab, click the OAW-IAP for

which you want to monitor the throughput. The

OAW-IAP view is displayed.

3. Study the Throughput graph. For example, the

graph shows 44.03 Kbps incoming traffic

throughput at 12:08 hours.

Table 10:

Access Point View — Usage Trends and Monitoring Procedures

The following table describes the RF trends graphs available in the client view:

Graph

Name

Description Monitoring Procedure

Signal The Signal graph shows the signal

strength of the client for the last 15 minutes.

It is measured in decibels.

To see an enlarged view, click the graph.

The enlarged view provides Last,

Minimum, Maximum, and Average signal

statistics of the client for the last 15

minutes.

To see the exact signal strength at a

particular time, move the cursor over the

graph line.

To monitor the signal strength of the selected client for

the last 15 minutes,

1. Log in to the AOS-W Instant UI. The Virtual

Controller view is displayed. This is the default view.

2. In the Clients tab, click the IP address of the client

for which you want to monitor the signal strength.

The client view is displayed.

3. Study the Signal graph in the RF Trends pane. For

example, the graph shows that signal strength for

the client is 54.0 dB at 12:23 hours.

Table 11:

Client View — RF Trends Graphs and Monitoring Procedures

AOS-W Instant 6.3.1.1-4.0 | User Guide AOS-W Instant User Interface | 58

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 334 335

Kommentare zu diesen Handbüchern

Keine Kommentare

Alcatel-Lucent IAP93 Betriebsanweisung Seite 58

Kommentare zu diesen Handbüchern